I always had some difficulty getting the free IPsecuritas connected so I am sure others had problems too. Various other trademarks are held by their respective owners.This was a tricky one. WatchGuard and the WatchGuard logo are registered trademarks or trademarks of WatchGuard Technologies in the United States and other countries. Verify the hosts behind the Firebox and behind the SonicWALL can successfully ping each other.Log in to the Dell SonicWALL TZ400 Web UI.Keep all default settings in Advanced VPN Settings.For VPN Policy bound to, from the adjacent drop-down list, select Interface X1.In the Advanced Settings section, select the Enable Keep Alive check box.Select the Enable Perfect Forward Secrecy check box.In the Ipsec (Phase 2) Proposal section, from the Protocol drop-down list, select ESP.From the Authentication drop-down list, select SHA256. From the Encryption drop-down list, select AES-256.From the DH Group drop-down list, select Group 14.In the IKE (Phase 1) Proposal section, from the Exchange drop-down list, select IKEv2 Mode.From the adjacent drop-down list, select WGINT. In the Remote Networks section, select Choose destination network from list.From the adjacent drop-down list, select X2 Subnet. In the Local Networks section, select Choose local network from list.For all other settings, keep the default values.In the adjacent text box, type the WatchGuard Firebox public IP address. From the Peer IKE ID drop-down list, select IPv4 Address.In the adjacent text box, type the SonicWALL outgoing public IP address. From the Local IKE ID drop-down list, select IPv4 Address.In the Shared Secret and Confirm Shared Secret text boxes, type the pre-shared secret key.In the IPsec Primary Gateway Name or Address text box, type the peer IP address.In the Name text box, type a descriptive name for this VPN.From the Authentication Method drop-down list, select IKE using Preshared Secret.From the Policy Type drop-down list, select Site to Site.In the VPN Policies section, click Add.Select Manage > Connectivity > VPN > Base Settings.In the Netmask/Prefix Length text box, type the netmask.In the Network text box, type the network address.From the Type drop-down list, select Network.From the Zone Assignment drop-down list, select VPN.In the Name text box, type the object name.Select Manage > Policies > Objects > Address Objects.For information about how to configure interfaces and zones, see the Dell SonicWALL TZ400 documentation. Log in to the Dell SonicWALL TZ400 Web UI at The default IP address is 192.168.168.168.This the local network protected by the Dell SonicWALL device.Ĭonfigure the Dell SonicWALL TZ400 Zone and Interface Settings In the Network IP text box, type the remote IP segment.In the Remote IP section, from the Choose Type drop-down list, select Network IPv4.This the local network protected by the Firebox. In the Network IP text box, type the local IP segment.In the Local IP section, from the Choose Type drop-down list, select Network IPv4.From the Gateway drop-down list, select the gateway that you configured.Keep all other Phase 1 settings as the default values.From the Version drop-down list, select IKEv2.In the Gateway Endpoint section, select the Start Phase 1 tunnel when Firebox starts check box.Keep the default settings for all other options.In the adjacent text box, type the IP address of your SonicWALL WAN connection.In the adjacent text box, type the primary IP address of the External Firebox interface.The Primary Interface IP Address is the primary IP address you configured on the selected external interface. From the Interface IP Address drop-down list, select Primary Interface IPv4 Address. From the External Interface drop-down list, select External.The Gateway Endpoint Settings dialog box opens. In the Gateway Endpoint section, click Add.From the drop-down list, select String-Based.In the adjacent text box, type the pre-shared key.In the Credential Method section, select Use Pre-Shared Key.
0 Comments
Leave a Reply. |